|Place of Origin:||Beijing,China|
|Minimum Order Quantity:||1 unit|
|Delivery Time:||within 5 working days|
|Payment Terms:||T/T, L/C, D/P, Western Union, MoneyGram|
|Supply Ability:||200 units per months|
|Material:||Ceramic Core,metal Sealed||Output Power:||20w|
|Wavelength:||10.6um||Color:||White And Grey|
|Beam Diameter:||<1.2||Power Stability:||+-5%|
20w CO2 Laser Tube long lifespan 10.6um for marking machine and beauty machine
Leading manufacturer of Metal RF co2 laser source in China:
DAVI Lasers is a reliable company for expert advice and good service in the field of co2 laser beam source. Superior beam quality,favourable price, long product lifetime ,efficient technical support are the main strengths of our products and service.
The DAVI Laser team listens, informs, communicates and shares its experience with all its customers in China and worldwide.Although it has installed thousands of systems, the challenge continues and the best is yet to come!
For Medical treatment
-CO2 Fractional Laser Scare Removal Skin Resurfacing Device
-CO2 laser therapy
-RF Stretch Marks Removal CO2 Fractional Laser Machine
-RF Tube Laser Generator Vaginal Tightening Laser
-Cosmetology surgery apparatus
For CO2 Laser Marking/Engraving Machine
-Achieve high speed static or dynamic online marking code
-High engraving and marking efficiency
Competitive Advantages of our laser machine:
1,3-5 years Long lifetime, Stable machine and mode quality
2, All metal body and very firm
3, Small size easy to carry
4, Quick response time nanosecond count
5, RF discharge, the top of machine covered with circuit
D20 specification and working condition
|Continuous rated output Power||20w|
|Power stability rate||±5%|
|Mode of quality||M2﹤1.2|
|Beam divergence angle||7.5±0.5m full angle|
|Degree of polarization||Linear polarization(﹥100:1) parallel to width direction|
|Working frequency &duty cycle||0～25KHZ,0～100%DC|
|Dimension L x W x H||
|Input voltage||36VDC±2%,max average current is 9A,peak current that power supply could hold up is 14A,it can’t be more than 1mS.|
|Max Heat Load||﹤430w|
|Maximum hull temperature||﹤60℃(140℉)|
|Working environment temperature||5℃～40℃(41℉～104℉)|
|Storage environment||－10℃～60℃(14℉～140℉),No condensation|
1. Laser power is tested according to the temperature of laser which is 25℃,everytime the laser temperature rises 1℃,the output power will reduce 1%.
2. Definition of stabilization: ±(Pmax－Pmin)/(2Pmax)
3. Testing condition of stabilization: Warming up about 10mins,controlling duty cycle constantly,under the normal operating environment.
D20 Signal Interface Description and Connector Pinout
|PIN NO||SIGNAL DESCRIPTION|
( PWM+ orange white)
TTL logic input ；1=RF ON,0=RF OFF；1KΩ impedance;
This input turns on the laser. See Pin7,Control Enable
+15VDC±0.5VDC,Max output for customer using is 0.25A
(Laser green white)
Laser status output
TTL logic output,1=LASER OK,0=LASER Fault;
When fault is not detected ,output valid
In case of temperature failure, the case temperature is below 60℃.
Temperature status output
TTL logical output,1=normal temperature,0= Ultra high temperature;
When the case temperature is below 60℃, the output is valid.
(Volt blue white )
Power and voltage status output
TTL logical output;1=normal voltage;
0= abnormal voltage;
|6(GND Green)||For internal use. must ground connected|
(Enable brown white)
TTL Logical input；1= Laser control enable,0=Laser controlled shutdown
This input must be valid before RF is enabled to turn on the laser.
1) The connector uses the RJ-45 type.
2) The color noted on pin can correspond to the cable color our company sent together with the product.
Contact Person: sarah