|Place of Origin:||China|
|Minimum Order Quantity:||1 Unit|
|Payment Terms:||T/T, D/P, D/A, L/C, Western Union|
|Supply Ability:||300 Units per Month|
|Average Output Power:||150W||Pulse Frequency:||0-100kHz|
|M²-Beam Quality:||﹤1.5||Beam Diameter（1/e²）:||2.2±0.6mm|
|Laser Head Weight:||15.9kg||Duty Cycle Adjustable Range:||0-60%|
M150 High Power Laser Tube Core Part in CO2 Laser Cutting Machine Improve process effect 40000 Hours Lifetime gas refillable
Davi Laser is devoted to provide high quality beam source to co2 Laser equipment. M150 is high power laser tube cooled by water . The small beam diameter and good M²-Beam quality can make sure fine effect in cutting and engraving work. Our profesional technical team can provide maintenance free after sales service and solve your problems in efficient way !
Comparing with Glass laser tube,RF co2 laser tubes is higher in price, but it has many distinct advantages. ﹤1.2 beam mode makes it perform well during the fine processing .
M150 specification and working condition:
|Specification parameter||Average output power||150W|
|Average power range||10-150W|
|Typical Properties||Peak power||375W|
|Pulse energy range||5-300mJ|
|Pulse rise and fall time||﹤90|
|Power stability rate||﹤±10%|
|The stability of the beam pointing||﹤200μrad|
|Beam cycle degree||﹤1.2:1|
|Beam divergence angle||﹤9mrad|
|Duty cycle adjustable range||0-60%|
|Degree of polarization||﹥100:1/Linear polarization|
|Power parameter||DC input voltage||48v±1%|
|DC input current||Max mean square root:50A,peak value:100A|
|Cooling water parameter||Cooling water speed||5.7L/min|
|Cooling water temperature range||10℃—35℃|
|Water Rigidity(CaCO3)||﹤250 mg/L|
|Environment parameter||Environment temperature||5℃—40℃|
|Relative Humidity<95% non condensation||﹤95% non condensation|
(1) Power test condition: Power pulse width 600μs, duty cycle 60%,25℃ cooling water. As temperature rise, the output power will decline.
(2) Power stability is defined as plus or minus ±(Pmax - Pmin)/2Pmax .
|M150 Signal Interface Description and Connector Pinout|
|DB25connector||Connect instruction||Signal instruction|
|7(+) and 20(-)||
modulation input signal
|This teminal requires input differential signal to control the output laser,when the signal is effective (high level)there is laser output; when the signal is invalid (zero level), there is no laser output. The pulse width of the signal should be between 10 and 998 ms,duty cycle less than 60% and the pulse frequency 0-100khz.|
Short circuit between pin3 and 16
|Enable radio frequency amplifier.Digital signal is effect when it is low, low level voltage input will enable the RF amplifier work.|
1. 48V 50A power supply, the power must have GND.
2. Pay attention to the dust proof of the laser output window,prevent the lens burn caused by dust pollution, especially when the output window is upward.
3. Prevent the back reflection of laser,any back reflection will cause the damage of laser.
4. We suggest to fix either front end or back end of the laser tube, but don’t fix them both when you assemble, the purpose is to prevent the laser cavity shape distortion being caused by heat-expansion and cold-contraction during use.
5. This laser module is water cooling , please run the water cooling machine before the laser starts to work.
When you have other questions in the using process, please contact with us for solution on time .
M150 assembly drawing
Contact Person: tracy