|Place of Origin:||China|
|Minimum Order Quantity:||1 unit|
|Payment Terms:||T/T, L/C, MoneyGram, Western Union|
|Supply Ability:||500 units per month|
|Beam Diameter:||1.8±0.2mm||Material:||Metal Sealed , Ceramic Cavity|
|Net Weight:||6.6KG||Cooling Way:||Air Cooling|
|Output Power:||30W Nominal , Average 37W In Actually||Dimension:||357×92.5×142mm|
30W co2 laser tube D30, metal sealed , RF excited , Ceramic laser tube ,
10.6um wavelength , high beam mode quality
Beijing Dawei Laser Technology Co., Ltd. is committed to providing innovative products for laser processing solutions. With a variety of products, state-of-the art engineering facilities and worldwide support, Dawei laser strives to meet the most advanced needs of our customers.
All of our products are built at our laser manufacturing facility in Beijing ,China and we keep adequate stock levels to quickly respond to your integration requirements.
Model D30 is 30w output laser tube with 10.6um wavelength. It is RF excited, metal sealed, the resonant cavity is made of ceramic. The lifetime is 10000 hours, the tube can be gas refilling when the output power is insufficient, which usually occurs after 5 years using.
Guarantee period is 18 months !
Competitive Advantages of DAVI laser:
1. 3-5 years Long lifetime, Stable machine and mode quality .
2. All metal body and very firm.
3. Small size easy to carry.
4. Quick response time nanosecond count.
5. RF discharge, the top of machine covered with circuit.
6. Favourable price, high performance-price ratio !
Model D30 Laser Specification and working condition
|Continuous rated output Power||30w|
|Power stability rate||±5%|
|Mode of quality||M2﹤1.2|
|Beam divergence angle||7.5±0.5m full angle|
|Degree of polarization||Linear polarization(﹥100:1)parallel to width direction|
|Working frequency &duty cycle||0～25KHZ,0～100%DC|
|Dimension L x W x H||
|Input voltage||48VDC±2% range,Average current max 12A,required power supply could bear peak current 18A no less than 1mS.|
|Max Heat Load||﹤575w|
|Maximum hull temperature||﹤60℃(140℉)|
|Working environment temperature||5℃～40℃(41℉～104℉)|
1.Laser power is tested according to the temperature of laser which is 25℃,everytime the laser temperature rises 1℃,the output power will reduce 1%.
2.Definition of stabilization: ±(Pmax－Pmin)/(2Pmax)
3.Testing condition of stabilization: Warming up about 10mins,controlling duty cycle constantly,under the normal operating environment.
D30 Signal Interface Description and Connector Pinout
|PIN NO||SIGNAL DESCRIPTION|
( PWM+ orange white)
TTL logic input ；1=RF ON,0=RF OFF；1KΩ impedance;
This input turns on the laser. See Pin7,Control Enable
|2(+15V orange)||+15VDC±0.5VDC,Max output for customer using is 0.25A|
(Laser green white)
Laser status output
TTL logic output,1=LASER OK,0=LASER Fault;
When fault is not detected ,output valid.
Temperature status output
TTL logical output,1=normal temperature,0= Ultra high temperature;
When the case temperature is below 60℃, the output is valid
(Volt blue white )
Power and voltage status output
TTL logical output;1=normal voltage;
0= abnormal voltage
|6(GND Green)||For internal use. must ground connected|
(Enable brown white)
TTL Logical input；1= Laser control enable,0=Laser controlled shutdown
This input must be valid before RF is enabled to turn on the laser.
1.The connector uses the RJ-45 type.
2.The color noted on pin can correspond to color of the cable color our company sent together with the product.
What can a Laser module D30 do in Application:
Contact Person: sarah