|Place of Origin:||China|
|Minimum Order Quantity:||1 Unit|
|Model:||M100||Cooling Way:||Water Cooling|
|Mode Of Quality:||﹤1.5||Beam Divergence Angle:||﹤9mrad|
|Input Current:||Max Mean Square Root:50A,peak Value:100A||Duty Cycle Adjustable Range:||0-60%|
150W Sealed CO2 Laser Tube Water Cooling High Stable Power Adjustable Good Beam Mode Perfect In Laser Engraving Cutting
M150: High Power co2 laser tube suitable for engraving and cutting different materials like wood, leather, cloths, MDF, thick paper and so on . It provide high quality beam source, M²-Beam quality is ﹤1.5, the output power can be adjustable . It is a maintenance free product.
M150 specification and working condition
|Specification parameter||Average output power||150W|
|Average power range||10-150W|
|Typical Properties||Peak power||375W|
|Pulse energy range||5-300mJ|
|Pulse rise and fall time||﹤90|
|Power stability rate||﹤±10%|
|The stability of the beam pointing||﹤200μrad|
|Beam cycle degree||﹤1.2:1|
|Beam divergence angle||﹤9mrad|
|Duty cycle adjustable range||0-60%|
|Degree of polarization||﹥100:1/Linear polarization|
|Power parameter||DC input voltage||48v±1%|
|DC input current||Max mean square root:50A,peak value:100A|
|Cooling water parameter||Cooling water speed||5.7L/min|
|Cooling water temperature range||10℃—35℃|
|Water Rigidity(CaCO3)||﹤250 mg/L|
|Environment parameter||Environment temperature||5℃—40℃|
|Relative Humidity<95% non condensation||﹤95% non condensation|
(1)Power test condition: Power pulse width 600μs,duty cycle 60%,25℃ cooling water. As temperature rise,the output power will decline.
(2)Power stability is defined as plus or minus ±(Pmax - Pmin)/2Pmax .
|M150 Signal Interface Description and Connector Pinout|
|DB25connector||Connect instruction||Signal instruction|
|7(+) and 20(-)||
modulation input signal
|This teminal requires input differential signal to control the output laser,when the signal is effective (high level)there is laser output; when the signal is invalid (zero level), there is no laser output. The pulse width of the signal should be between 10 and 998 ms,duty cycle less than 60% and the pulse frequency 0-100khz.|
Short circuit between pin3 and 16
|Enable radio frequency amplifier.Digital signal is effect when it is low, low level voltage input will enable the RF amplifier work.|
1. 48V 50A power supply, the power must have GND.
2. Pay attention to the dust proof of the laser output window,prevent the lens burn caused by dust pollution, especially when the output window is upward.
3. Prevent the back reflection of laser,any back reflection will cause the damage of laser.
4. We suggest to fix either front end or back end of the laser tube, but don’t fix them both when you assemble, the purpose is to prevent the laser cavity shape distortion being caused by heat-expansion and cold-contraction during use.
5. This laser module is water cooling , please run the water cooling machine before the laser starts to work.
When you have other questions in the using process, please contact with us for solution on time .
M150 water cooling integrated model drawing
Questions : What problems must we pay attention to during the storage and transport process ?
Answer : First, during the storage and transport process,please make sure the cooling water stored inside the laser tube has been dried up completely. We recommend Purity 99.95% dry nitrogen to blow dry. If not,the remained cooling water may cause irreparable damage to the laser tube. Secondly, the beam output window should be sealed during storage and transport process, in case the beam output window being polluted. Thirdly, in order to prevent the unexpected impact to damage the laser tube, please handle it gently during storage and transport. At the same time , please make sure the water pipe of the laser tube doesn’t bear force,in case to prevent the water pipe shape distortion.
Questions : What are the requirements for the use of the laser?
Answer:1) Environmental temperature should be kept at 5 ℃ to 40 ℃ when necessary to use air conditioner .
2) Environmental cleanliness,in the case of the laser without external dustproof equipment, high dust degree will cause the laser window to burn out.
3) Environment humidity requires the phenomenon of non condensation of laser.
4) Environmental acid-base degree keeps neutral.
Contact Person: tracy